How to put trucks on a longboard? There are a few ways to put trucks on a longboard. The easiest way is to use the bolts that come with the trucks. Another way is to use risers, which are plastic or metal spacers that go between the board and the truck.
Risers help to prevent wheel bite, which is when the wheels rub against the deck of the board.
- Place the longboard on a level surface
- Center the trucks on the longboard deck, making sure that they are evenly spaced out
- Use a Phillips head screwdriver to tighten or loosen the kingpin nut, depending on which way you want the trucks to turn
- Test the trucks by pushing on them from different angles to see how they respond
How To: Install Trucks on a Drop Thru with Scott Lembach | MuirSkate Longboard Shop
Which Way Do You Put Trucks on a Longboard?
There are a few things to consider when mounting trucks on a longboard. The first is the width of the trucks. You’ll want to make sure that the trucks you select are not too wide or too narrow for your longboard.
The second is the kingpin. You’ll want to make sure that the kingpin is facing the correct way so that it doesn’t come loose while riding. Finally, you’ll want to make sure that the bolts are tightened properly so that they don’t come loose while riding.
Putting trucks on a longboard is a straightforward process. Here’s a step-by-step guide:
- Gather Necessary Tools and Materials:
- Longboard deck
- Two trucks
- Eight bolts and nuts (usually provided with the trucks)
- Skateboard tool or wrench and screwdriver
- Align the Trucks with the Deck:
- Place your longboard deck on a flat surface.
- Align the trucks with the holes on the deck. The kingpin and bushings of the trucks should face inward towards the center of the deck.
- Attach the Trucks:
- Insert the bolts through the top of the deck and through the holes in the trucks.
- Screw the nuts onto the bolts from the underside of the deck. Start by hand to ensure they’re properly threaded.
- Tighten the Bolts:
- Use the skateboard tool or wrench and screwdriver to tighten the bolts. It’s important not to overtighten, as this can damage the deck or trucks.
- Check the Alignment:
- Once tightened, double-check to ensure the trucks are properly aligned. They should be parallel to each other and the edges of the deck.
- Test the Setup:
- Stand on the board and lean side to side to test the trucks’ responsiveness. Adjust the tightness of the kingpin nut if necessary for desired turning sensitivity.
- Safety Check:
- Ensure all bolts are secure and there is no wobbling or loose parts.
Remember, the tightness of the trucks and the wheels can significantly affect your riding experience. It’s common to adjust these a few times to find what works best for your style of riding. Also, always ensure that you’re using appropriate safety gear like a helmet when riding your longboard.
Can You Put Any Trucks on a Drop Through Longboard?
The answer to this question is a bit complicated and depends on a few factors. The first factor is the width of the trucks. Most drop through longboards have a width of 8.0-8.5 inches, which means that they can accommodate trucks with a width of up to 8.5 inches.
However, there are some drop through longboards with a width of 9.0 inches, which means that they can accommodate trucks with a width of up to 9 inches. The second factor is the height of the trucks. Most drop through longboards have truck mounts that are flush with the top of the deck, but there are some models that have truck mounts that are slightly raised above the deck.
This can affect what kinds of trucks can be used with the board. Finally, the third factor is the type of truck you want to use. Some trucks, such as reverse kingpin (RKP) trucks, are not compatible with drop through boards because their hangers are too wide or their baseplates are too thick.
Other types of trucks, such as standard kingpin (SKP) trucks, may be compatible with some drop through boards but not others depending on the factors mentioned above. In general, though, it is best to use RKP or SKP trucks with a width that matches the width of your drop through longboard for optimal performance and stability.
Do Longboard Trucks Face in Or Out?
There’s a lot of debate on this topic, but the general consensus seems to be that longboard trucks face in. This is because it provides more stability and control when going downhill, and makes it easier to do tricks. However, some people prefer to have their trucks face out because they feel it gives them more maneuverability.
Ultimately, it’s up to personal preference.
Can You Put Longboard Trucks on a Regular Skateboard?
You can put longboard trucks on a regular skateboard, but it is not recommended. Longboard trucks are designed for stability and speed, while regular skateboard trucks are designed for tricks and turns. The different design of the trucks will make your skateboard ride differently.
If you’re looking to go fast and straight, then longboard trucks are the way to go. But if you’re looking to do tricks and turns, then regular skateboard trucks are the better option.
Credit: www.youtube.com
How to Put Trucks on a Skateboard
If you’re like most people, the thought of putting a truck on a skateboard probably seems pretty impossible. But with a little bit of know-how, it’s actually not that hard to do! Here’s how-to put trucks on a skateboard:
1. First, you’ll need to remove the wheels from the trucks. To do this, simply unscrew the axle nuts with a wrench or socket set.
2. Next, place the trucks upside down on the skating surface. You may want to use tape or another adhesive to keep them in place.
3. Now it’s time to put the wheels back on – but this time, they’ll be facing inwards towards each other. Make sure that the bearings are properly seated in each wheel before screwing on the axle nuts (hand tight is usually sufficient).
4. Finally, stand up on the skateboard and enjoy your ride! Just be sure to go slowly at first until you get used to the feel of riding with inverted trucks.
How to Tighten Skateboard Trucks?
Tightening the trucks on your skateboard is crucial for stability and control. Here are two methods – with or without tools:
- With Tools: Use a skate tool or a wrench to tighten the kingpin nut on each truck. Start by loosening it slightly, then gradually tighten it until you reach your desired level of tightness. Remember to keep both sides equally tight to maintain balance.
- Without Tools: If you don’t have any tools handy, you can use the “kickflip method”. Stand with one foot on the skateboard, tilt it to one side, and kick down with your other foot to create force that tightens the truck. Repeat this on both sides until you achieve the desired tightness.
Remember, finding the right level of tightness is a personal preference. Experiment with different levels until you find what works best for your riding style.
FAQs Of How to Put Trucks On A Longboard?
What Tools Do I Need to Install Trucks on a Longboard?
- You will need a skateboard tool or a wrench and screwdriver. These tools are used to tighten the nuts and bolts that secure the trucks to the deck.
How Do I Know Which Way the Trucks Should Face?
- The trucks should be mounted so that the kingpins and bushings (the larger, central bolt and rubber cushions) face inward towards the center of the board. This orientation is crucial for proper turning mechanics.
What Size Hardware is Required for Mounting Trucks?
- Typically, you’ll need eight bolts and nuts, usually 1″ to 1.5″ in length. The exact size can vary depending on the thickness of your deck and whether you use risers.
Do I Need Risers for My Longboard?
- Risers, which are placed between the deck and the trucks, are not always necessary but can be used to prevent wheel bite (when the wheel touches the deck during turns) and to provide a smoother ride. The need for risers depends on the size of your wheels and your riding style.
How Tight Should the Trucks Be on the Longboard?
- The tightness is a matter of personal preference and depends on your riding style. Generally, they should be tight enough to be secure but not so tight that they cause the board to warp or the bolts to be over-stressed.
Can I Use Any Skateboard Trucks for a Longboard?
- While skateboard and longboard trucks are similar, they are not always interchangeable. Longboard trucks are typically wider to match the width of longboard decks and offer different turning dynamics.
How Do I Adjust the Trucks After Installation?
- You can adjust the tightness of the kingpin nut to change how easily the board turns. Tightening it will make the board more stable but less responsive, while loosening it will make it more responsive but less stable.
Is It Necessary to Use All Eight Bolts and Nuts?
- Yes, for safety and stability, it’s essential to use all provided hardware. This ensures even distribution of stress and prevents the trucks from becoming loose over time.
How Do I Ensure the Trucks Are Properly Aligned?
- The trucks should be parallel to each other and the edges of the deck. After mounting, visually inspect and make sure they are aligned straight.
What Maintenance Is Required After Installing Trucks?
- Regularly check the tightness of the nuts and bolts, as they can loosen over time. Also, inspect the trucks for any signs of wear or damage, especially if you frequently ride your longboard.
Conclusion
In order to put trucks on a longboard, you will need to follow these steps: 1. Place the longboard on a level surface. 2. Align the holes in the baseplate of the truck with the corresponding holes in the longboard deck.
3. Insert bolts through the holes and use a wrench to tighten them in place. 4. Repeat this process for the other truck.
Hi, my name is Gabriel. I am completed my MBA from private university and my subject was IT (Information Technology) and also I complete my graduation form South East University and Department from CSE (Computer Science & Engineering). I am author and blogger of this website who loves to write about different topics that are related to the board sport. From beginner tips to intermediate advice, I want to offer you quality content that will help improve your skill set and make you a better rider. Thanks for checking out my site!
